7. Moving Resources¶
7.1. Moving Resources Manually¶
There are primarily two occasions when you would want to move a resource from its current location: when the whole node is under maintenance, and when a single resource needs to be moved.
7.1.1. Standby Mode¶
Since everything eventually comes down to a score, you could create constraints for every resource to prevent them from running on one node. While Pacemaker configuration can seem convoluted at times, not even we would require this of administrators.
Instead, you can set a special node attribute which tells the cluster “don’t
let anything run here”. There is even a helpful tool to help query and set it,
called crm_standby. To check the standby status of the current machine,
run:
# crm_standby -G
A value of on indicates that the node is not able to host any resources,
while a value of off says that it can.
You can also check the status of other nodes in the cluster by specifying the –node option:
# crm_standby -G --node sles-2
To change the current node’s standby status, use -v instead of -G:
# crm_standby -v on
Again, you can change another host’s value by supplying a hostname with
--node.
A cluster node in standby mode will not run resources, but still contributes to quorum, and may fence or be fenced by nodes.
7.1.2. Moving One Resource¶
When only one resource is required to move, we could do this by creating
location constraints. However, once again we provide a user-friendly shortcut
as part of the crm_resource command, which creates and modifies the extra
constraints for you. If Email were running on sles-1 and you wanted it
moved to a specific location, the command would look something like:
# crm_resource -M -r Email -H sles-2
Behind the scenes, the tool will create the following location constraint:
<rsc_location id="cli-prefer-Email" rsc="Email" node="sles-2" score="INFINITY"/>
It is important to note that subsequent invocations of crm_resource -M are
not cumulative. So, if you ran these commands:
# crm_resource -M -r Email -H sles-2
# crm_resource -M -r Email -H sles-3
then it is as if you had never performed the first command.
To allow the resource to move back again, use:
# crm_resource -U -r Email
Note the use of the word allow. The resource can move back to its original
location, but depending on resource-stickiness, location constraints, and
so forth, it might stay where it is.
To be absolutely certain that it moves back to sles-1, move it there before
issuing the call to crm_resource -U:
# crm_resource -M -r Email -H sles-1
# crm_resource -U -r Email
Alternatively, if you only care that the resource should be moved from its current location, try:
# crm_resource -B -r Email
which will instead create a negative constraint, like:
<rsc_location id="cli-ban-Email-on-sles-1" rsc="Email" node="sles-1" score="-INFINITY"/>
This will achieve the desired effect, but will also have long-term
consequences. As the tool will warn you, the creation of a -INFINITY
constraint will prevent the resource from running on that node until
crm_resource -U is used. This includes the situation where every other
cluster node is no longer available!
In some cases, such as when resource-stickiness is set to INFINITY, it
is possible that you will end up with nodes with the same score, forcing the
cluster to choose one (which may not be the one you want). The tool can detect
some of these cases and deals with them by creating both positive and negative
constraints. For example:
<rsc_location id="cli-ban-Email-on-sles-1" rsc="Email" node="sles-1" score="-INFINITY"/>
<rsc_location id="cli-prefer-Email" rsc="Email" node="sles-2" score="INFINITY"/>
which has the same long-term consequences as discussed earlier.
7.2. Moving Resources Due to Connectivity Changes¶
You can configure the cluster to move resources when external connectivity is lost in two steps.
7.2.1. Tell Pacemaker to Monitor Connectivity¶
First, add an ocf:pacemaker:ping resource to the cluster. The ping
resource uses the system utility of the same name to a test whether a list of
machines (specified by DNS hostname or IP address) are reachable, and uses the
results to maintain a node attribute.
The node attribute is called pingd by default, but is customizable in order
to allow multiple ping groups to be defined.
Normally, the ping resource should run on all cluster nodes, which means that you’ll need to create a clone. A template for this can be found below, along with a description of the most interesting parameters.
| Resource Parameter | Description |
|---|---|
| dampen | The time to wait (dampening) for further changes to occur. Use this to prevent a resource from bouncing around the cluster when cluster nodes notice the loss of connectivity at slightly different times. |
| multiplier | The number of connected ping nodes gets multiplied by this value to get a score. Useful when there are multiple ping nodes configured. |
| host_list | The machines to contact in order to determine the current connectivity status. Allowed values include resolvable DNS connectivity host names, IPv4 addresses, and IPv6 addresses. |
Example ping resource that checks node connectivity once every minute
<clone id="Connected">
<primitive id="ping" class="ocf" provider="pacemaker" type="ping">
<instance_attributes id="ping-attrs">
<nvpair id="ping-dampen" name="dampen" value="5s"/>
<nvpair id="ping-multiplier" name="multiplier" value="1000"/>
<nvpair id="ping-hosts" name="host_list" value="my.gateway.com www.bigcorp.com"/>
</instance_attributes>
<operations>
<op id="ping-monitor-60s" interval="60s" name="monitor"/>
</operations>
</primitive>
</clone>
Important
You’re only half done. The next section deals with telling Pacemaker how to
deal with the connectivity status that ocf:pacemaker:ping is recording.
7.2.2. Tell Pacemaker How to Interpret the Connectivity Data¶
Important
Before attempting the following, make sure you understand rules. See the “Rules” chapter of the Pacemaker Explained document for details.
There are a number of ways to use the connectivity data.
The most common setup is for people to have a single ping target (for example, the service network’s default gateway), to prevent the cluster from running a resource on any unconnected node.
Don’t run a resource on unconnected nodes
<rsc_location id="WebServer-no-connectivity" rsc="Webserver">
<rule id="ping-exclude-rule" score="-INFINITY" >
<expression id="ping-exclude" attribute="pingd" operation="not_defined"/>
</rule>
</rsc_location>
A more complex setup is to have a number of ping targets configured. You can require the cluster to only run resources on nodes that can connect to all (or a minimum subset) of them.
Run only on nodes connected to three or more ping targets
<primitive id="ping" provider="pacemaker" class="ocf" type="ping">
... <!-- omitting some configuration to highlight important parts -->
<nvpair id="ping-multiplier" name="multiplier" value="1000"/>
...
</primitive>
...
<rsc_location id="WebServer-connectivity" rsc="Webserver">
<rule id="ping-prefer-rule" score="-INFINITY" >
<expression id="ping-prefer" attribute="pingd" operation="lt" value="3000"/>
</rule>
</rsc_location>
Alternatively, you can tell the cluster only to prefer nodes with the best
connectivity, by using score-attribute in the rule. Just be sure to set
multiplier to a value higher than that of resource-stickiness (and
don’t set either of them to INFINITY).
Prefer node with most connected ping nodes
<rsc_location id="WebServer-connectivity" rsc="Webserver">
<rule id="ping-prefer-rule" score-attribute="pingd" >
<expression id="ping-prefer" attribute="pingd" operation="defined"/>
</rule>
</rsc_location>
It is perhaps easier to think of this in terms of the simple constraints that
the cluster translates it into. For example, if sles-1 is connected to all
five ping nodes but sles-2 is only connected to two, then it would be as if
you instead had the following constraints in your configuration:
How the cluster translates the above location constraint
<rsc_location id="ping-1" rsc="Webserver" node="sles-1" score="5000"/>
<rsc_location id="ping-2" rsc="Webserver" node="sles-2" score="2000"/>
The advantage is that you don’t have to manually update any constraints whenever your network connectivity changes.
You can also combine the concepts above into something even more complex. The
example below shows how you can prefer the node with the most connected ping
nodes provided they have connectivity to at least three (again assuming that
multiplier is set to 1000).
More complex example of choosing location based on connectivity
<rsc_location id="WebServer-connectivity" rsc="Webserver">
<rule id="ping-exclude-rule" score="-INFINITY" >
<expression id="ping-exclude" attribute="pingd" operation="lt" value="3000"/>
</rule>
<rule id="ping-prefer-rule" score-attribute="pingd" >
<expression id="ping-prefer" attribute="pingd" operation="defined"/>
</rule>
</rsc_location>